instagram

ponderlabs

Pythagorean to the rescue. Now to place some hard

Pythagorean to the rescue. Now to place some hard stops to easily resquare against next time I need to check for square.

This clamp project has brought to light an issue.

This clamp project has brought to light an issue. No squarezies.

Tight pockets. Thinking it will loosen a bit over

Tight pockets. Thinking it will loosen a bit over time. Can always make them wider.

Instagram post 17966577257340324

Instagram post 17966577257340324

Instagram post 18004174867579254

Instagram post 18004174867579254

Instagram post 18353850937005122

Instagram post 18353850937005122

Instagram post 17895483059717911

Instagram post 17895483059717911

Time to change up my clamping game.

Time to change up my clamping game.

I love milling red heart. #cncrouter #cncwoodwo

I love milling red heart.

#cncrouter
#cncwoodworking
#ponderlabs

@goosebaylumber In case you were wondering what I

@goosebaylumber
In case you were wondering what I do with your wood 👌

#cncwoodworking
#cncrouter

I miss my CNC hammer since I broke it on the table

I miss my CNC hammer since I broke it on the table build. Time for a new and improved version.

#cncrouter
#cncwoodworking
#ponderlabs

After a weekend of removing and installing motors

After a weekend of removing and installing motors while troubleshooting, time for a victory song.

#cncrouter
#cncwoodworking

Ready for oil. #cncwoodworking #cncrouter

Ready for oil.

#cncwoodworking
#cncrouter

Last two corner blocks installed. Glue done. Now h

Last two corner blocks installed. Glue done. Now hand sanding and oil.

#cncrouter
#cncwoodworking
#ponderlabs

One day I will own a flush cut saw like grownups d

One day I will own a flush cut saw like grownups do. 😉

#cncwoodworking
#cncrouter
#ponderlabs

Shoutout to VBeltSupply for getting my belt to me

Shoutout to VBeltSupply for getting my belt to me so quickly.
My other orders from CNC suppliers have not even shipped yet.

#cncrouter
#cncwoodworking
#ponderlabs

The cool thing about CNC’s is that if you see so

The cool thing about CNC’s is that if you see something odd and ignore it, they break down pretty quick 😀
I’ve been eyeing that thread on the belt for a couple months now.
Unreliable X axis behavior the whole time.
By time I sorted out the issue I was down 16 board feet of rough sawn oak.

#ponderlabs
#cncrouter
#cncwoodworking

Sanded until I was doing more harm than good. #c

Sanded until I was doing more harm than good.

#cncrouter
#cncwoodworking
#ponderlabs

Looking good. #cncrouter #ponderlabs #cncwoodw

Looking good.

#cncrouter
#ponderlabs
#cncwoodworking

Trim done. Only 10.73 hours of sanding to go. 😉

#cncrouter
#cncrouterwork
#cncwoodworking

Load More… Follow on Instagram

Ponder Labs

Chasing down bugs in this one. My stepper motors would stop in the middle of a job for no reason. Well, there was a reason, but I really don't understand why.

Did some epoxy testing this time around. Ran into a few issues as usual, but got it done. Pretty happy with the results.

----
"Concentration" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 3.0 License
http://creativecommons.org/licenses/by/3.0/
----

Bandsaw table. The entire table is assembled with just glue and wood dowels. No metal fasteners. This one took longer than it should have. Notes in comments.

---
"Relaxing Piano Music" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 3.0 License
http://creativecommons.org/licenses/by/3.0/

A lot going on in this one. Finished the spoil board. Added magnetic skirts. Did a little tramming and knocked out a few issues to boot.

Thanks for watching.

It was a bit of a battle but we now have a two layer spoilboard to ready for surfacing.

Load More… Subscribe